Electronic Multistage INOX Water Booster Set with Brio Tank 900W – 1.25Hp 5CRm 100 Pedrollo

Fully automatic booster pump system featuring a multistage stainless steel pump and electronic controller. Ideal for water supply in homes without municipal water or where water pressure is insufficient. Also suitable for garden irrigation, small industrial applications, and any situation that requires water pressure boosting.

The electronic pump controller is a device mounted directly on the pump (single-phase or three-phase), either vertically or horizontally depending on the flow direction. It automates the start of the pump when pressure drops (e.g., opening a tap) and stops it when the maximum pressure is reached (e.g., closing the tap). It can control pumps ranging from 0.5Hp to 2Hp.

The operation of the pump is controlled by the Brio Tank electronic unit. The pump starts when pressure drops below the minimum threshold and stops when the upper limit is reached. The motor is copper-wound, compact, and designed for ease of use.

Multistage Pumps

Multistage pumps offer excellent flow rates and high head performance with low energy consumption. They are reliable, quiet, and efficient—ideal for boosting pressure and irrigating gardens. Their typical maximum suction height is approximately 8 meters.

The 5CRm 100 pump features 5 stainless steel impellers, a stainless steel AISI 304 pump body and shaft, and is suitable for transporting clean water or other non-corrosive liquids similar to water. Recommended for well pumping, garden irrigation, pressure boosting, and general domestic water supply. The pump should only be used with clean water, free of abrasive particles or chemicals that could damage its internal components.

The installation must be in a well-ventilated area, protected from extreme weather conditions.

Dry-Run Protection:

If the tank or well runs dry and the pump starts pulling air, the system will stop immediately to prevent pump damage.

Advantages of the Brio Tank Controller:

• Prevents frequent start/stop cycles in cases of low water demand or small leaks in the system thanks to its built-in 0.4L water reservoir

• Protection from moisture and humidity with a sealed electronic circuit housing

• Dry-run automatic reset at the press of a button

• Overpressure protection – stops the pump at a preset limit

• Easy integration into domestic or light industrial installations

Technical Specifications:

• Model: 5CRm 100

• Pump Type: Multistage

• Power: 1.25 HP – 900W

• Inlet/Outlet: 1" x 1"

• Pump Body: Stainless Steel AISI 304

• Impellers: Stainless Steel

• Shaft: Stainless Steel AISI 304

• Number of Impellers: 5

• Low noise operation

• Full copper winding

• Integrated thermal protection for single-phase motors

• Insulation Class: F

• Protection Rating: IPX4

• Voltage/Frequency: 220V / 50Hz

• Max Flow Rate: 7800 L/h

• Max Head: 63m

• Max Suction Depth: 7m

• Max Pressure: 6.3 bar

• Min Fluid Temperature: -10°C

• Max Fluid Temperature: 40°C

• Max Ambient Temperature: 40°C

• Product Code: 108394

Includes:

 

• Single-phase Multistage Stainless Steel Pump Pedrollo 5CRm 100 1.25Hp – click on the image to view more specifications.

 

• Brio Tank Electronic Pump Control Unit – click on the image to view more specifications.

Advantage of the New Motor:

• Pedrollo and its engineers are constantly working to improve motor efficiency by using the same or even less energy.

• The 5CRm 100 model has been upgraded — its new motor is now manufactured at 1.25Hp, while maintaining the same pump performance in terms of maximum head and flow rate (previously with a 1.5Hp motor).

• Through this optimization, Pedrollo aims to reduce energy consumption as well as environmental emissions.

Enjoy the performance and quality of your new and improved Pedrollo pump.

It is recommended to use an expansion tank in combination with the electronic controller for the following reasons:

• To prevent frequent starts of the pump

• To stabilize flow and avoid pressure fluctuations in the system

• To protect the hydraulic components of the pump and the installation from water hammer

• To prevent air entrapment in the system

• To reduce electricity consumption

To view potable water expansion tanks, click on the image below: